How to Reset Whirlpool Dishwasher [In 2 Minutes]

It is very common for a dishwasher to stop working from the middle of a cycle. Almost most of the old model dishwasher has this serious problem.

However, most of these minor issues can be fixed by resetting the dishwasher. Yes, resetting the dishwasher fixes most minor issues in the dishwasher.

It configures a new setting in your dishwasher and runs the new cycle that works to most problems.

How to reset Whirlpool dishwasher?

How to Reset Whirlpool Dishwasher

Whirlpool dishwashers don’t have such a fixed button to reset the dishwasher. So, you can reset the dishwasher by turning the power off button.

Similarly, if the power button is not working, you can plug the power of the dishwasher.

Now you have to wait a couple of minutes until the heat and motor inside the dishwasher get cool down. After a couple of minutes, turn on the power of the dishwasher.

Now the dishwasher is successfully reset. If there was some problem, then it should be fixed now. In the newer model, there is a separate button for reset.

All you need to do is press the power or reset button and hold it for a couple of minutes. 

Tips for resetting Whirlpool dishwasher

Depending upon the dishwasher model, there are various ways to reset the dishwasher. Moreover, in the older dishwasher model, there is no such button to reset the dishwasher.

You need to reset the dishwasher manually. Here we will discuss two different ways to reset the Whirlpool dishwasher.

Resetting control board

The dishwasher can be easily reset from the control board. However, in some cases, the control board might not work properly or stop working.

This often happens where there is a power outage or surge in the dishwasher.

In this situation, you should reboot your dishwasher to function properly. Here is what you should do to bring the dishwasher to work.

1. Press the power button if it works perfectly in your dishwasher. If not, then remove or switch off the power cable from the dishwasher. 

2. Now you should wait for 10 to 15 minutes to bring the dishwasher into functioning. 

3. After waiting for 10 to 15 minutes, plug the power in your dishwasher and then turn on the power button.

4. Now select the high setting from your control panel. 

5. After this, select any heat setting from the control panel to dry the dishes you are doing. Now, wait for a couple of minutes and repeat the cycle selection and see if the dishwasher is working properly or not

This is how you can reset the Whirlpool dishwasher from the control panel. There is nothing to worry about if this method doesn’t work in your dishwasher. We will discuss another process to reset the dishwasher.

How to Reset Whirlpool Dishwasher Practical Video

Diagnostic mode

The diagnostic mode can be very helpful, especially when your dishwasher is flashing light and producing a beeping sound.

I am sure most of you might have encountered this error in your dishwasher once. Diagnostic mode is a kind of feature that forces the dishwasher to reset. Here is step-wise instruction to enable diagnostic mode in the dishwasher. 

1. Press the “Heated Dry” button and “Normal” Button simultaneously in your dishwasher.

2. Press the “Heated Dry” Button again in your dishwasher, followed by the “Normal” Button. This will force the dishwasher to enter into Diagnostic mode. 

This is how you can enable diagnostic mode and eventually reset your dishwasher. This method should work in almost every newer and older model of dishwasher. If this method doesn’t work, then try considering this method again. If the problem persists, don’t worry. We will discuss another way to reset the dishwasher.

User manual

If none of the above methods works in your dishwasher, you should be using an older dishwasher version.

Or you are not following the above steps properly. However, there is nothing to worry about if you have a user manual. 

The user manual contains all the information about the dishwasher, including resetting techniques, error codes, and solution to other major problems.

The user manual includes step-wise instructions to fix the issues in the dishwasher. 

Moreover, you will also find the solution for the error codes. The Whirlpool dishwasher displays various error codes, which helps us know how to identify the particular problem.

That is stopping the dishwasher from working. If you don’t know error codes, then don’t worry. We will discuss everything about this topic later in the article. 

Why should you reset the dishwasher?

As of now, most of us know why one should reset the dishwasher. Is it safe to reset the dishwasher again and again?

Does resetting the dishwasher fix issues on the dishwasher? There might be lots of questions going inside your head.

It is common to have such a question if you are tired of fixing the problem in the dishwasher. 

There are many reasons why you need to reset the dishwasher. There is some situation in which dishwasher stop functioning and create problem.

This problem can often not be fixed unless we restart the cycle. When you reset the dishwasher, all the old settings will be reset.

This allows the dishwasher to perform correctly without misleading the dishwasher’s configuration setting. 

Most of the older models of dishwashers don’t feature to reset the dishwasher using the button.

It needs to be manually reset, but nowadays, almost every dishwasher has this feature to reset the dishwasher. This has made it easy to solve error codes and other minor problems.

What to do after resetting the dishwasher?

Resetting the dishwasher takes somewhere around 10 to 15 minutes. After this, you check the configuration of the dishwasher.

There are lots of things that you can check on your dishwasher. The first one is to check the water pressure and temperature of the water. 

Besides this, check if the sensor has moisture or not. If there is moisture, give some time to dry; otherwise, this same problem could omit error codes.

You can also check the drainage pipe, clean the dispenser with water, and fill in new detergent.

What not to do to avoid malfunctioning?

Electrical appliances need proper cleaning and care like other things and devices in your home.

Similarly, your dishwasher also needs cleaning and maintenance, then only it can perform well. Here are some points which you can follow to avoid dishwasher malfunctioning.

1.     The dishwasher filter needs to be clean from time to time as it gets clogged with food scrap, which could cause malfunctioning.

2.     Water pressure and temperature are other reasons behind the dishwasher malfunctioning. It is recommended that water temperature should be between 50 to 60 degrees Fahrenheit.

3.     Power surge and the electrical outage is another major issue that could cause power surges in the dishwasher. So, it is recommended to install power surge protection for the dishwasher.

4.     You should always check the rinse aid, and you need to make sure that it is not decreased too much. 

5.     Rust is another reason for the malfunctioning of the dishwasher. The metal inside the rock can get rust after many cycles of water exposure. So, to avoid this thing from happening, you can touch up the chips using paint. The paint is not that expensive and available in the supermarket. 

6.     Keep the drain clear from the food scrap. Food can get stuck in the gutter, so it is necessary to clean the drain from time to time to prevent the dishwasher from omitting error codes or LED light.

What is the error code in the Whirlpool dishwasher?

In the above section, we have discussed a lot about error codes. I am sure you might notice and even with the two-letter codes in your dishwasher.

Error codes are an indicator in the dishwasher that helps us understand the dishwasher’s problem.

They are a very useful feature that allows us to fix the issues before our dishwasher malfunctions. There are different types of error codes displayed by dishwashers. 

If you have a user manual, you will find the meaning of almost every error code there. But, I am sure some of you don’t have the user manual to search the meaning of particular error codes.

Unlike other dishwashers, the Whirlpool dishwasher doesn’t show error codes. It flashes LED light under which we have to understand the error. 

Here is the list of error codes shown by Whirlpool dishwasher:

1.     F01(Anti-flooding overflow): 

●      LED 6: on

●      LED 7: off

●      LED 8: off

●      LED 9: off

2.     F02(Water fill solenoid valve failure):

●      LED 6: off

●      LED 7: on

●      LED 8: off

●      LED 9: off

3.     F03(Water drain failure):

●      LED 6: on

●      LED 7: on

●      LED 8: off

●      LED 9: off

4.     F04(Thermostat Fault):

●      LED 6: off

●      LED 7: off

●      LED 8: on

●      LED 9: of

5.     F06(Water fill timeout):

●      LED 6: off

●      LED 7: on

●      LED 8: on

●      LED 9: off

6.     F07(Water turbine damage):

●      LED 6: on

●      LED 7: on

●      LED 8: on

●      LED 9: off

7.     F08(Temperature timeout fault):

●      LED 6: on

●      LED 7: off

●      LED 8: off

●      LED 9: on

8.     F09(Software error):

●      LED 6: on

●      LED 7: off

●      LED 8: off

●      LED 9: on

9.     F10(Heating element fault):

●      LED 6: off

●      LED 7: on

●      LED 8: off

●      LED 9: on

10. F11(Wash pump failure):

●      LED 6: on

●      LED 7: on

●      LED 8: off

●      LED 9: on

11. F12(Mainboard & Display communication error):

●      LED 6: off

●      LED 7: off

●      LED 8: on

●      LED 9: on

12. F13(Mainboard fault):

●      LED 6: on

●      LED 7: off

●      LED 8: on

●      LED 9: on

13. F15(Virtual communication):

●      LED 6: on

●      LED 7: on

●      LED 8: on

●      LED 9: on

These are some of the most shown error codes in the Whirlpool dishwasher. Now, I hope you can figure out these error codes by seeing the above-LED combination.

There are different ways to fix these errors, and one of the common methods to correct these errors is resetting the dishwasher.

In most cases, resetting works, but sometimes you need to see your user manual about the problem.

Maybe Required in Future:-

Conclusion

I hope that now you can reset the Whirlpool dishwasher without any problems. We have discussed different methods to reset the dishwasher and error codes often shown or displayed by the dishwasher. You don’t have to worry about the minor issues now. You can easily fix it by resetting the dishwasher. 

Frequently Asked Questions

What happens when you reset your dishwasher? (80)

When you reset the dishwasher, it will cool down the motor and different parts of the dishwasher. This will help the dishwasher function properly while running a new cycle. 

How to fix a dishwasher that is not draining? (80)

When the dishwasher is not draining, it means that the bottom unit of the dishwasher should be filled with food scrap. So, what you can do is run the garbage disposal or clean your sink’s air gap. Clear all the standing water from the drainage pipe and also make sure to check the Drain hose.

How to reset the whirlpool dishwasher?

The Whirlpool dishwasher can be reset by pressing the power or reset button and holding it for a couple of minutes. After this, the dishwasher should reset. This method may not work in the older model. To reset the older model dishwasher, simply turn off the power button and turn it on after 10 to 15 minutes. 

How to clean a dishwasher?

On the upper rack of the dishwasher, there is a safe container. Here put a cup of vinegar and run a hot water cycle in your dishwasher. This will wash away all bad odor, oily surfaces, and grease. After this run, another hot water cycle will remove the remaining oily cover and grease from the dishwasher. 

Does the Whirlpool dishwasher have a reset button?

Whirlpool does have a reset button but only in the newer model of the dishwasher. But, there is no need to reset the button. You can reset the dishwasher by pressing the power off button. 

I am Kevin Technician and this website is created with the purpose to help common people to find proper information about Dishwasher. Feel free to comment or email your queries.